Getting "no IPv4 addresses" With isc-dhcp-server And Subinterfaces

I have tried both subinterfaces and secondary ip address route and neither are working for isc-dhcp-server. It is refusing to pull the proper IP's. I am using Debian 8 Jessie and ISC-DHCP-SERVER 4.3.1. My /etc/network/interfaces ## Corporate Network auto eth0 allow-hotplug eth0 iface eth0 inet manual ## New Subnet auto eth0:0 allow-hotplug eth0:0 iface eth0:0 inet static address 10.0.0.2 gateway 10.0.0.1 netmask 255.255.0.0 dns-nameservers 127.0.0.1 10.0.0.3 dns-search example.net dns-domain example.net ## Old Subnet auto eth0:1 allow-hotplug eth0:1 iface eth0:1 inet static address 10.136.136.253 netmask 255.255.255.0 ifconfig eth0 Link encap:Ethernet HWaddr b8:27:eb:c0:59:e5 inet6 addr: fe80::ba27:ebff:fec0:59e5/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:26688 errors:0 dropped:69 overruns:0 frame:0 TX packets:7301 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:7174565 (6.8 MiB) TX bytes:1286716 (1.2 MiB) eth0:0 Link encap:Ethernet HWaddr b8:27:eb:c0:59:e5 inet addr:10.0.0.2 Bcast:10.0.255.255 Mask:255.255.0.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 eth0:1 Link encap:Ethernet HWaddr b8:27:eb:c0:59:e5 inet addr:10.136.136.253 Bcast:10.136.136.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 ip add 2: eth0: mtu 1500 qdisc pfifo_fast state UP group default qlen 1000 link/ether b8:27:eb:c0:59:e5 brd ff:ff:ff:ff:ff:ff inet 10.0.0.2/16 brd 10.0.255.255 scope global eth0:0 valid_lft forever preferred_lft forever inet 10.136.136.253/24 brd 10.248.28.255 scope global eth0:1 valid_lft forever preferred_lft forever inet6 fe80::ba27:ebff:fec0:59e5/64 scope link valid_lft forever preferred_lft forever /var/log/syslog when starting isc-dhcp-server Aug 12 09:48:20 ns01 dhcpd: Wrote 0 deleted host decls to leases file. Aug 12 09:48:20 ns01 dhcpd: Wrote 0 new dynamic host decls to leases file. Aug 12 09:48:20 ns01 dhcpd: Wrote 5544 leases to leases file. Aug 12 09:48:21 ns01 dhcpd: Aug 12 09:48:21 ns01 dhcpd: No subnet declaration for eth0:1 (no IPv4 addresses). Aug 12 09:48:21 ns01 dhcpd: ** Ignoring requests on eth0:1. If this is not what Aug 12 09:48:21 ns01 dhcpd: you want, please write a subnet declaration Aug 12 09:48:21 ns01 dhcpd: in your dhcpd.conf file for the network segment Aug 12 09:48:21 ns01 dhcpd: to which interface eth0:1 is attached. ** Aug 12 09:48:21 ns01 dhcpd: Aug 12 09:48:21 ns01 dhcpd: Aug 12 09:48:21 ns01 dhcpd: No subnet declaration for eth0:0 (no IPv4 addresses). Aug 12 09:48:21 ns01 dhcpd: ** Ignoring requests on eth0:0. If this is not what Aug 12 09:48:21 ns01 dhcpd: you want, please write a subnet declaration Aug 12 09:48:21 ns01 dhcpd: in your dhcpd.conf file for the network segment Aug 12 09:48:21 ns01 dhcpd: to which interface eth0:0 is attached. ** Aug 12 09:48:21 ns01 dhcpd: Aug 12 09:48:21 ns01 dhcpd: failover peer failover: I move from normal to startup Aug 12 09:48:21 ns01 dhcpd: Server starting service.