Beaglebone cannot connect to internet using ethernet cable

I've been trying to get my Beaglebone Black to connect to internet using an ethernet cable plugged direct into my Netgear router. I have tried many things but nothing has worked so far. Here are some relevant outputs. systemctl # Yesterday, internet not working ● networking.service loaded failed failed Raise network interfaces # Today after reflashing beaglebone, internet still not working networking.service loaded active exited Raise network interfaces ip address 1: lo: mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: can0: mtu 16 qdisc noop state DOWN group default qlen 10 link/can 3: can1: mtu 16 qdisc noop state DOWN group default qlen 10 link/can 4: eth0: mtu 1500 qdisc mq state UP group default qlen 1000 link/ether a0:f6:fd:8a:ec:7e brd ff:ff:ff:ff:ff:ff inet 192.168.0.10/24 brd 192.168.0.255 scope global eth0 valid_lft forever preferred_lft forever inet 192.168.0.123/24 brd 192.168.0.255 scope global secondary eth0 valid_lft forever preferred_lft forever inet6 2600:8806:502:b00:a2f6:fdff:fe8a:ec7e/64 scope global mngtmpaddr dynamic valid_lft 86390sec preferred_lft 86390sec inet6 fe80::a2f6:fdff:fe8a:ec7e/64 scope link valid_lft forever preferred_lft forever ip route default via 192.168.0.1 dev eth0 68.105.28.11 via 192.168.0.1 dev eth0 68.105.28.12 via 192.168.0.1 dev eth0 68.105.29.11 via 192.168.0.1 dev eth0 192.168.0.0/24 dev eth0 proto kernel scope link src 192.168.0.10 192.168.0.1 dev eth0 scope link 192.168.6.0/30 dev usb1 proto kernel scope link src 192.168.6.2 linkdown 192.168.7.0/30 dev usb0 proto kernel scope link src 192.168.7.2 linkdown 212.227.81.55 via 192.168.0.1 dev eth0 host google.com ;; connection timed out; no servers could be reached ping www.google.com ping: www.google.com: Temporary failure in name resolution ping 192.168.0.1 (router) PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data. --- 192.168.0.1 ping statistics --- 9 packets transmitted, 0 received, 100% packet loss, time 8199ms ping 192.168.0.39 (my computer, connected to same router via ethernet) PING 192.168.0.39 (192.168.0.39) 56(84) bytes of data. 64 bytes from 192.168.0.39: icmp_seq=1 ttl=64 time=0.432 ms 64 bytes from 192.168.0.39: icmp_seq=2 ttl=64 time=0.324 ms 64 bytes from 192.168.0.39: icmp_seq=3 ttl=64 time=0.389 ms 64 bytes from 192.168.0.39: icmp_seq=4 ttl=64 time=0.387 ms --- 192.168.0.39 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 3004ms rtt min/avg/max/mdev = 0.324/0.383/0.432/0.038 ms I have no idea how to fix this. It started working yesterday when I started writing this question then it started working mysteriously. I rebooted this morning and it's not working again.