wpa_supplicant says network is disabled

When trying to connect to a network (specifically a WPA2 enterprise network for a university) with wpa_supplicant on Gentoo Linux, the network is shown as disabled when the flag is not set. My wpa_supplicant.conf : ctrl_interface=/var/run/wpa_supplicant network={ ssid="TheNetwork" eap=PEAP identity="redacted" password="redacted" ca_cert="/etc/ssl/certs/AddTrust_External_Root.pem" ca_path="/etc/ssl/certs/" phase1="peapver=0" phase2="auth=MSCHAPV2" } network={ ssid="Another network that works" key_mgmt=NONE disabled=1 # This is obviously not normally disabled } network={ ssid="Yet another working network" psk="redacted" disabled=1 # Likewise } Output of sudo wpa_supplicant -iwlp3s0 -c/etc/wpa_supplicant/wpa_supplicant.conf -d, with repetitive lines removed: wpa_supplicant v2.6 random: Trying to read entropy from /dev/random Successfully initialized wpa_supplicant Initializing interface 'wlp3s0' conf '/etc/wpa_supplicant/wpa_supplicant.conf' driver 'default' ctrl_interface 'N/A' bridge 'N/A' Configuration file '/etc/wpa_supplicant/wpa_supplicant.conf' -> '/etc/wpa_supplicant/wpa_supplicant.conf' Reading configuration file '/etc/wpa_supplicant/wpa_supplicant.conf' ctrl_interface='/var/run/wpa_supplicant' Priority group 0 id=0 ssid='TheNetwork' id=1 ssid='Another network that works' id=2 ssid='Yet another working network' nl80211: Supported cipher 00-0f-ac:1 ... nl80211: Supported cipher 00-0f-ac:9 nl80211: Using driver-based off-channel TX nl80211: Driver-advertised extended capabilities (default) - hexdump(len=8): 00 00 00 00 00 00 00 40 nl80211: Driver-advertised extended capabilities mask (default) - hexdump(len=8): 00 00 00 00 00 00 00 40 nl80211: interface wlp3s0 in phy phy0 nl80211: Set mode ifindex 4 iftype 2 (STATION) nl80211: Subscribe to mgmt frames with non-AP handle 0x55701974e5f0 nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x55701974e5f0 match=0104 nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x55701974e5f0 match=040a nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x55701974e5f0 match=040b ... rfkill: initial event: idx=1 type=1 op=0 soft=0 hard=0 netlink: Operstate: ifindex=4 linkmode=1 (userspace-control), operstate=5 (IF_OPER_DORMANT) Add interface wlp3s0 to a new radio phy0 nl80211: Regulatory information - country=US (DFS-FCC) nl80211: 2402-2472 @ 40 MHz 30 mBm nl80211: 5170-5250 @ 80 MHz 23 mBm nl80211: 5250-5330 @ 80 MHz 23 mBm (DFS) nl80211: 5490-5730 @ 160 MHz 23 mBm (DFS) nl80211: 5735-5835 @ 80 MHz 30 mBm nl80211: 57240-63720 @ 2160 MHz 40 mBm nl80211: Added 802.11b mode based on 802.11g information wlp3s0: Own MAC address: [redacted] wpa_driver_nl80211_set_key: ifindex=4 (wlp3s0) alg=0 addr=(nil) key_idx=0 set_tx=0 seq_len=0 key_len=0 ... wpa_driver_nl80211_set_key: ifindex=4 (wlp3s0) alg=0 addr=(nil) key_idx=5 set_tx=0 seq_len=0 key_len=0 wlp3s0: RSN: flushing PMKID list in the driver nl80211: Flush PMKIDs wlp3s0: No enabled networks (3 disabled networks) wlp3s0: State: DISCONNECTED -> INACTIVE ENGINE: Loading dynamic engine ENGINE: Loading dynamic engine EAPOL: SUPP_PAE entering state DISCONNECTED EAPOL: Supplicant port status: Unauthorized nl80211: Skip set_supp_port(unauthorized) while not associated EAPOL: KEY_RX entering state NO_KEY_RECEIVE EAPOL: SUPP_BE entering state INITIALIZE EAP: EAP entering state DISABLED Using existing control interface directory. ctrl_iface bind(PF_UNIX) failed: Address already in use ctrl_iface exists, but does not allow connections - assuming it was leftover from forced program termination Successfully replaced leftover ctrl_iface socket '/var/run/wpa_supplicant/wlp3s0' wlp3s0: Added interface wlp3s0 wlp3s0: State: INACTIVE -> DISCONNECTED nl80211: Set wlp3s0 operstate 0->0 (DORMANT) netlink: Operstate: ifindex=4 linkmode=-1 (no change), operstate=5 (IF_OPER_DORMANT) random: Got 20/20 bytes from /dev/random EAPOL: disable timer tick What sticks out to me is the line wlp3s0: No enabled networks (3 disabled networks). This appears despite the fact that there are clearly only two disabled networks. Further evidence that the first network is being disabled despite the lack of a disabled=1 flag is that when running the wpa_supplement command with the other two networks *enabled*, a scan is performed and output, but all relevant APs are skipped as "disabled", "SSID mismatch", and "SSID mismatch", even though the SSIDs clearly do match. When running wpa_supplicant with the other two networks removed, the line wlp3s0: No enabled networks (1 disabled networks) appears. What in the configuration is causing this to occur?